HeadphonesA cameraman would never judge composition and good lighting based on what he or she hears. Likewise, a soundperson would be a fool to record audio based solely on what they see.

Yet all too often, that is exactly what many filmmakers do. They see their audio meters reacting, and therefore assume that good audio is being recorded. Headphones apparently only serve the purpose of keeping one's neck warm; besides, we all know that they mess up a good hair.

Am I just wisecracking? I wish I was, but sadly, there are way too many filmmakers out there who do not take monitoring their audio seriously. In the classes that I instruct, I will often (purposely) disconnect the audio feed from the mixer to the camera, and then ask everyone after the take, "How is everything? Picture good? Sound okay?"

Right:  HeadphonesSony MDR-7506 Professional Headphones.
Long considered to be a standard of the industry.

More times than not, the camera operator (with headphones draped over their neck) will grin and give us a thumbs up! Perhaps the camerman stopped paying attention to any audio, and just concentrated on picture. Or maybe he/she just assumed that the live audio from the actors was what was being recorded. Bottom line: no usable audio.

There is absolutely no excuse for waiting until the shooting day is long over before evaluating the soundtrack. Thinking that the sound is fine is not the same thing as checking that the sound is fine. Use headphones; and playback some takes before you move on to the next major setup.

There are some very simple remedies. To begin with, the soundmixer, boom operator, and camera operator should all be wearing (over the ears, not around the neck) a pair of high quality headphones.

At least once every few takes, the boom operator should gently tap the mic with his finger, or slide his finger along the windscreen. Check with the camera operator to make sure that he hears that disturbance clearly in his headphones. If, for any reason the camera is not properly connected to the mixing panel or boom mic, it would be impossible for the cameraman to hear the finger tap. Ditto, if the camera somehow got switched to only pick up audio from the built-in camera mic.

Let's examine the issue of headphones. It is imperative that the soundperson invest in a high quality pair of Professional recording/engineering headphones, such as those made by Sony, Audio Technica, and Sennheiser.
Headphones intended for location audio recording share the following characteristics:

They need to fit comfortably OVER THE EARS, as opposed to just being a foam pad that sits against the ear. Professional headphones should provide a modicum of acoustic isolation by surrounding your earlobe with a cushioned pad.

The frequency response needs to be FLAT, so that what you record is what you hear. You do NOT want any headphones that "improve" the sound by boosting high or low frequencies, nor adding "concert hall" reverb. Avoid the so-called "noise canceling" headphones because they alter what you hear.

Impedance value for your phones should be between 40 ohms to 80 ohms. 50 to 65 ohms are most common. Less than 40 ohms and your audio will readily distort. Higher than 80 or so, and the volume will be too low. Remember, these headphones are intended to be used with field recorders and mixers; not home stereo receivers. Fancy 600 ohm headphones are fine for music listening at home because your powered stereo receiver puts out a very powerful signal; but plug them in to your camcorder and you will barely hear a thing.

Another spec to look at is the maximum wattage that the drivers (headphones) can accept before self-destructing. Many inexpensive headphones will blow out one or both sides if they are subjected to a short, but loud burst of audio (such as the ear-splitting crackle made by a faulty connection). Good headphones can accept a full watt or more without damaging. Cheaper phones can become worthless with hits of as little as one or two tenths of a watt!

Get into the habit of cleaning the inside of your headphones with an alcohol prep pad (readily available in the drugstore for those who self-inject; no prescription needed; and only a couple dollars for a box of 100 or more). You do not even want to think about what kinds of germs can flourish in a sweat fed environment.

Headphone cords are naturally way too long. If it is a straight cable, then fold it up into a neat bundle and secure it with some wraps or cable ties. (Don't use an adhesive tape that will leave sticky residue.) If you are blessed with a coiled cable, here is a trick for managing it. Tie a cord at the start of the coils, and thread that cord through the center of the all of the coils. Tie it off at the other end. That will prevent the coiled cord from stretching out. Should you ever need the extra length, just untie one end of the cord.

Once you have acquired your headphones, the next step is to learn how to use them.

Adjust your listening volume so that normal dialogue is smack in the middle of your comfort zone. A loud burst of dialogue, such as a shout or a scream, should be slightly uncomfortable (but not painful) to hear. Loud enough so that, if you were on a telephone, you would want move the handset a little bit away from your ear.

If an actor barely whispers, you should reflexively want to concentrate hard or make it louder.

Monitor2Left: The CT100 is not only a versatile cable tester,
but also provides mic or line level test tones.
You can read more about it

Won't the meter on the camera or When you using a mixing panel, you can adjust your headphone volume relative to the tone generator. Turn on the tone, and set it so that it reads at zero on the mixer. Then gradually raise the headphone volume until the tone is slightly uncomfortable, just like loud dialogue. Remember, than when you mix audio levels, zero should NOT represent normal conversation. Those levels should be several dB below zero.

It is natural for every individual to set their headphone listening level to a different physical volume knob setting. Our hearing and sensitivity vary from person to person. It is also normal for a mixer to reset his or her headphone volume throughout the day. Our hearing is more sensitive in the mornings, and becomes fatigued as the day wears on. Indoor locations tend to be quieter, so we need less volume. Outdoors, we tend to boost our listening levels. What matters in the long run, though, is that we maintain normal dialogue in our comfort zone.

When you set your headphone volume too loud, you tend to mix your audio levels too low. On the same token, if you listen at too low of a volume, you will end up recording way too hot.

mixing board indicate proper recording levels? Yes, they will, but you should not be watching them too closely. It is akin to driving a car: if you spend all of your time watching the speedometer, you will hit a tree. You drive by watching the road around you, and gauge your speed by your surroundings. You only glance down at the speedometer now and then (usually when a cop car is present).

The same should hold true for adjusting your audio levels. Keep your eyes on the actors, and pay attention to their body language. That will tell you who is about to talk, and warn you of shouts, sneezes, and coughs. Note the position of actors relative to your mics. Are they right under the boom, or off of their marks. Where are they relative to other mics on the set?

Do not wait until you HEAR a problem. Learn to observe and anticipate. When you drive, you do not watch your foot move from gas to brake pedal. When you mix, you should not watch your own fingers either.

Use your eyes to keep track of the scene, and allow your ears to prompt you into raising or lowering the audio levels.

Next month we continue with the special requirements of the Boom Operator.